![what frame is a smith and wesson model 10 what frame is a smith and wesson model 10](https://rogersgunsandgrips.com/wp-content/uploads/2020/11/fullsizeoutput_f7d-scaled.jpeg)
Though certainly one of Smith & Wesson’s top performers, the Model 327 TRR8 does come at a price: the revolver is listed on the Smith & Wesson website at nearly $1,400 - though like all S&W firearms, is backed by the company’s lifetime service policy, guaranteeing the revolver against any manufacturing defects. And though I wouldn’t consider myself defenseless with this Model 13 and a couple of speedloaders, I’m not going to be trying to buy one for my primary defensive sidearm.The Model 327 TRR8 is part of Smith & Wesson’s Performance Center line-up, and features several improvements that aid in accuracy compared to a stock configuration and make them “top performers.” The TRR8, therefore, features a Performance Center action and trigger. This gun would make a fine collector’s piece or range toy. My conclusion: I don’t know how those FBI agents and NY State Troopers did it but they did – out of necessity. Believe me, I’m no sight snob and I’m fine with black-on-black as long as they are sufficiently large and defined. Still, I was fully prepared to give them the benefit of the doubt. However, the grips and old sights on this thing are unacceptable.
![what frame is a smith and wesson model 10 what frame is a smith and wesson model 10](https://i.pinimg.com/736x/9a/c8/85/9ac8854cedb547ed4c11b6b2fa09f596.jpg)
It shoots like a dream and has that perfect, K-Frame balance. It is absolutely gorgeous and the lockup is as tight as any I’ve ever seen. I’ll be honest – I really wanted to love the Smith & Wesson Model 13.
![what frame is a smith and wesson model 10 what frame is a smith and wesson model 10](https://i.ebayimg.com/images/g/yjkAAOSwsX5hT7Gs/s-l1600.jpg)
357 Magnum load I try in it, and just a bit above point of aim with most. The revolver hits point of aim at 20 yards with just about every. Though lighter than my preferred range revolver, the M13 is a pleasure to shoot with the new grips installed.Īccuracy is quite good despite the sights. The gun was far more usable with quality grips installed. Instead, I threw on a set of Pachmayr Presentation Grips. I love the look of these grips, but couldn’t abide their awkward feel on the range. I fired a handful of rounds (literally one cylinder full) with the factory wooden grips before giving up. Looking this hammer it is obvious that this gun is of the pre-MIM era. The lockup on this particular revolver is one of the tightest I’ve ever personally experienced. This Model 13 is a pre-lock gun with a hammer-mounted firing pin. These should come off before a range session and get replaced with a set of Pachmayr Presentation Grips. They place the knuckle of your middle finger directly behind the trigger guard where it gets pummeled by recoil. Designed to optimize trigger reach back in the days when single-action firing was the preferred technique, these grips are tremendously awkward during double-action fire. The factory wooden “splinter grips” with inset S&W medallions are gorgeous and the gun owes a lot of its looks to them. On the range I found the combination of black-on-black, getting completely lost in the black target. Were I relying on this revolver, I would definitely have to do something to the sights to make them a little more visible. Adjustable sights were once perceived as being fragile and prone to breakage. The rear sight on this gun was once acceptable – even preferable in some circles – to the larger adjustable sights we are used to today. This revolver is reminiscent of a simpler time, for better and worse. Unfortunately such a beautiful finish picks up every little smudge and fingerprint… it is hard to believe finishes like these were once standard from the factory. It is absolutely gorgeous and work like this is seldom seen these days. Also note the blueing on this particular gun. Though not especially well-suited to rapid acquisition, the fixed sights on this model do lend an attractive flat-top profile to the revolver. I do really appreciate the aesthetics of the bull-barrel on the Model 13. This model is somewhat lesser known than the Models 10 and 65 but typifies the 4″, K-Frame’s quick-handling and balance. Though also made with in a 3″ round butt configuration, the one I got my hands on is a Model 13-4 with a 4″ barrel and square butt. I thought you all might enjoy a look at this retro revolver here! Smith & Wesson Model 13 I recently got to spend a little time with this revolver and I’m glad that I did. It is functionally identical to the stainless steel Model 65. Like its little brother (the Model 10) the 13 is a blued steel model and features a bull barrel and fixed sights. Once issued by both the New York State Police and the FBI, the Smith & Wesson Model 13 is K-Frame.